網站首頁
產品目錄
機構設置
企業文化
聯繫我們

產品目錄 

山泉MS-1955硅烷改性密封膠

型號︰-
品牌︰山泉
原產地︰中國
單價︰-
最少訂量︰-
分享到:

 共有 15 相關信息  
12345下一個

產品描述

   山泉MS-1955硅烷改性密封膠

MS-1955  modified silane sealant

            

●產品描述Description

山泉MS-1955為中高強度硅烷改性密封膠,單組份、濕氣固化,不含溶劑及異氰酸酯,耐候性、耐老化性能優良,固化快,固化過程中及固化后不會產生任何有害物質,對多種基材有很好的附着力,且表面可漆。

SHANQUAN MS-1955 is mid strength MS sealant .It is cured by reacting with moisture in air at room temperature free of solvents ,isocyanate , good climate resistance,good aging resistance .During the curing process, it won’t produce any poison and pollution on the base surface. Wide range of adhesion with variable basic material,can be painted over .

技術數據Technical Date

外觀  Appearance

 

白、灰色膏狀物

White, Grey paste

 

表干時間(25℃/55RH%) min

Tack free time

 

15-60min

 

固化速度25℃/55RH%), mm/24h

Curing speed

3.0

密度, Density   g/cm3  

1.4±0.1

邵氏A硬度  Shore A hardness

35-50

拉伸強度,MPa

Tensile strength

2.0

斷裂伸長率,%

 Break elongation

300

固含量 

Solid Content  

98%

耐紫外線(UV

UV-Resistance

建議施工溫度

Application  Temperature

5-35

服務溫度

Service temperature

-40-100

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 以上數據測試條件溫度23±2℃,相對濕度55%±5%養護時間168h

    Test condition: Ts23±2,RH55%±5%, 168h.

應用範圍 Areas of Application

山泉MS-1955適合一般結構的粘接,可用於汽車、船舶、風電、集裝箱、電子、軌道交通、空調安裝室外防水密封等領域,如船舶內外裝飾件的粘接與密封,金屬與塑料的彈性及抗震粘接。

Bonding to the general structure,as a bonding sealant in automobile,watercraft,wind-electricity,container-manufacture,electronic,rail transit ,the crust of outdoor air conditioning  for waterproof ,elastic bonding in  decoration of ship ,metal and plastics working.

施工方法Method of Application

   1.用棉紗清除塗膠部位表面的塵土、油污及明水。如果表面有易剝落鏽蝕物質,應事先用金屬刷清除,必要時根據情況選擇活化劑、丙酮等有機溶劑擦拭表面。

   2.如需打磨,建議打磨后用活化劑處理基材表面,並乾燥5—10分鐘后再施膠。

   3.根據施工部位的形狀將密封膠的尖嘴切成一定形狀的大小,用手動或氣動膠槍將膠塗在施工部位.

   4.縫隙中鼓出的膠可用刮板刮平或肥皂水抹平。如有的部位不慎被膠所污染,則儘早用汽油或酒精等溶劑清除。如膠已固化,需要用刀片切割或打磨。

  1.Cleaning away dust, greasy dirt and clear water of the glued surface by cotton yarn. If the surface contains rust , which should be in advance cleaned away by metallic brush, in addition to, can also wipe the surface.

  2.The nozzle is sheared as required size and screwed on the sealant ,then the sealant with the nozzle is used by the manually-operated or the compressed-Air pistol.

  3.The superfluous sealant from the gap may be pared off by the pattern strickle or suds. It is necessary to be cleared away at once by using benzene if the rest part is polluted by the sealant. It is necessary to cut or burnish by knife if the sealant cured.

包裝Package                       

400ml、600ml軟包裝                 Sausage    400ml,  600ml

55加侖/                          Drum

貯存 storage

建議在25℃以下的乾燥庫房內,避免高溫/水汽,貯存期一般為9個月。

We suggest the products should be stored in the dry place bellow 25℃ ,avoid high temperature and moisture. The shelf life is nine months.

注意事項 Attention

1.開封后應當天用完,否則需嚴格密封保存。

 If the sealant is opened, it should be used up the same day; otherwise it should be conserved strictly.

2.在溫度15-35℃、濕度55%-75%RH條件下施工 。

 The best work condition is at the temperature of 15-35℃ and at the degree of humidity of 55%-75% RH.

 

 

 

產品圖片


相關產品
山泉牌AM-120D焊縫密封膠
山泉牌AM-120D焊縫密封膠
山泉AMS-1360聚氨酯改性密封膠
山泉AMS-1360聚氨酯改性密封膠
山泉建築結構密封膠
山泉建築結構密封膠
山泉防水膨脹密封膠
山泉防水膨脹密封膠




網站首頁  |  產品目錄  |  機構設置  |  企業文化  |  聯繫我們  |  網站地圖  |  手機版
  简体版     繁體版

Powered by DIYTrade.com  自助建站,永久免費!