网站首页
产品目录
机构设置
企业文化
联系我们

产品目录 

山泉MS-1955硅烷改性密封胶

型号︰-
品牌︰山泉
原产地︰中国
单价︰-
最少订量︰-
分享到:

 共有 15 相关信息  
12345下一个

产品描述

   山泉MS-1955硅烷改性密封胶

MS-1955  modified silane sealant

            

●产品描述Description

山泉MS-1955为中高强度硅烷改性密封胶,单组份、湿气固化,不含溶剂及异氰酸酯,耐候性、耐老化性能优良,固化快,固化过程中及固化后不会产生任何有害物质,对多种基材有很好的附着力,且表面可漆。

SHANQUAN MS-1955 is mid strength MS sealant .It is cured by reacting with moisture in air at room temperature free of solvents ,isocyanate , good climate resistance,good aging resistance .During the curing process, it won’t produce any poison and pollution on the base surface. Wide range of adhesion with variable basic material,can be painted over .

技术数据Technical Date

外观  Appearance

 

白、灰色膏状物

White, Grey paste

 

表干时间(25℃/55RH%) min

Tack free time

 

15-60min

 

固化速度25℃/55RH%), mm/24h

Curing speed

3.0

密度, Density   g/cm3  

1.4±0.1

邵氏A硬度  Shore A hardness

35-50

拉伸强度,MPa

Tensile strength

2.0

断裂伸长率,%

 Break elongation

300

固含量 

Solid Content  

98%

耐紫外线(UV

UV-Resistance

建议施工温度

Application  Temperature

5-35

服务温度

Service temperature

-40-100

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 以上数据测试条件温度23±2℃,相对湿度55%±5%养护时间168h

    Test condition: Ts23±2,RH55%±5%, 168h.

应用范围 Areas of Application

山泉MS-1955适合一般结构的粘接,可用于汽车、船舶、风电、集装箱、电子、轨道交通、空调安装室外防水密封等领域,如船舶内外装饰件的粘接与密封,金属与塑料的弹性及抗震粘接。

Bonding to the general structure,as a bonding sealant in automobile,watercraft,wind-electricity,container-manufacture,electronic,rail transit ,the crust of outdoor air conditioning  for waterproof ,elastic bonding in  decoration of ship ,metal and plastics working.

施工方法Method of Application

   1.用棉纱清除涂胶部位表面的尘土、油污及明水。如果表面有易剥落锈蚀物质,应事先用金属刷清除,必要时根据情况选择活化剂、丙酮等有机溶剂擦拭表面。

   2.如需打磨,建议打磨后用活化剂处理基材表面,并干燥5—10分钟后再施胶。

   3.根据施工部位的形状将密封胶的尖嘴切成一定形状的大小,用手动或气动胶枪将胶涂在施工部位.

   4.缝隙中鼓出的胶可用刮板刮平或肥皂水抹平。如有的部位不慎被胶所污染,则尽早用汽油或酒精等溶剂清除。如胶已固化,需要用刀片切割或打磨。

  1.Cleaning away dust, greasy dirt and clear water of the glued surface by cotton yarn. If the surface contains rust , which should be in advance cleaned away by metallic brush, in addition to, can also wipe the surface.

  2.The nozzle is sheared as required size and screwed on the sealant ,then the sealant with the nozzle is used by the manually-operated or the compressed-Air pistol.

  3.The superfluous sealant from the gap may be pared off by the pattern strickle or suds. It is necessary to be cleared away at once by using benzene if the rest part is polluted by the sealant. It is necessary to cut or burnish by knife if the sealant cured.

包装Package                       

400ml、600ml软包装                 Sausage    400ml,  600ml

55加仑/                          Drum

贮存 storage

建议在25℃以下的干燥库房内,避免高温/水汽,贮存期一般为9个月。

We suggest the products should be stored in the dry place bellow 25℃ ,avoid high temperature and moisture. The shelf life is nine months.

注意事项 Attention

1.开封后应当天用完,否则需严格密封保存。

 If the sealant is opened, it should be used up the same day; otherwise it should be conserved strictly.

2.在温度15-35℃、湿度55%-75%RH条件下施工 。

 The best work condition is at the temperature of 15-35℃ and at the degree of humidity of 55%-75% RH.

 

 

 

产品图片


相关产品
山泉牌AM-120D焊缝密封胶
山泉牌AM-120D焊缝密封胶
山泉AMS-1360聚氨酯改性密封胶
山泉AMS-1360聚氨酯改性密封胶
山泉建筑结构密封胶
山泉建筑结构密封胶
山泉防水膨胀密封胶
山泉防水膨胀密封胶




网站首页  |  产品目录  |  机构设置  |  企业文化  |  联系我们  |  网站地图  |  手机版
  简体版     繁體版

Powered by DIYTrade.com  自助建站,永久免费!